NOTICE - This website is ONLY for our customers and employees. If you have not bought from us you are not authorized to view this document. Also GreatVacs and any of its parent or child companies are not liable for any work you do on your vacuum. If your vacuum needs repaired or fixed in any way you need to send it to an authorized repair center. Any work done by anyone reading this document assumes all liability and risks to themselves, others around them and any property that may be damaged. Great Vacs has written this document for informational purposes only and assumes no risk or liability in any way. Thanks, Dustin

The main steps to adjusting the transmission is taking the vacuum apart to be able to get to the transmission. The following steps are how to take it apart. CLICK ON ANY OF THE THUMBNAILS TO SEE FULL SIZED PICTURE!

	WARNING: NEVER ATTEMPT TO PERFORM ANY TYPE OF MAINTENANCE OR WORK ON THE VACUUM IN ANY WAY WHILE VACUUM IS CONNECTED TO A POWER SOURCE. DOING SO MAY RESULT IN ELECTRIC SHOCK. Remove the Powerhead To do this you will select your carpet height adjuster to its highest settings. Then spin the belt lifter so the two red arrows are pointed at each other. Then disconnect the head and take it off. Side note - when you are done and put your head back on don't forget to realign the arrows to green on green.
	Remove the bag and handle Right where the handle goes into the actual vacuum it snaps out. To unsnap the handle their is a button on the back of the handle right at the base where it goes into the vacuum. To take off the bag put your hand under the boot mini emptor (plastic part at bottom of bag) and pull away from the vacuum and it snaps off. That is how you take off the handle and bag.
	Remove the trim around the Pivot handle The next step is to remove the trim around the pivot handle (where the handle snaps in). The first thing you want to do is to undo the screw at the bottom of the trim. The screw is located right above the transmission switch. Then you want to remove the screw that holds the cord under the trim. When that is off you want to unsnap the trim buy grabbing the bottom of it and lift up and at the same time push toward the front of the vacuum. The trim then comes off.
	Remove the Metal Body With the powerhead and rear trim removed the 4 screws that remove the Metal body are now visible. First we remove the 2 on the rear of the metal that were covered up by the trim. Once those are removed we move to the front of the vacuum and remove the two remaining screws that are holding on the front of the trim. With the 4 screws removed now you simply lift the Metal body off of the vacuum.

	Before Adjusting the transmission If your transmission is not working in either direction then do this step first. If your transmission is working in one direction but not the other then you can skip this step. What we want to do in this step is to make sure all the linkage is connected. Really the only link that I ever check is the one pictured. Sometimes the linkage pops out and that is the reason that the transmission is not working. If that is the problem put it where it should go and go below to testing the transmission.
	Adjusting the Transmission We are now ready to adjust the transmission. First we want to locate the two large adjusting screws (see picture). You will need to get a large phillips head screw driver and loosen them. Then you will want to move the bracket up or down in the direction it needs adjusted and then tighten the screws again. A point to be made here is that you just need to experiment one direction or another until you get it correct. For example I don't know which direction yours needs adjusted so you will have to do it one way or another until you get it right. So lets say that you transmission only works going forward and just barely going back. So you adjust the screws and re-tighten them, test the vacuum and now it works even faster going forward and none at all going back then you know that you moved it in the wrong direction. So then you simply loosen the screws again and move it in the opposite direction until you get the desired adjustment.
	Testing your adjustments Now you are ready to test your adjustment to make sure it's correct. To do that you are going to resnap the handle and bag on. Then you will put the powerhead back on. We put this on because kirbys have saftey switches so that the vacuum will not turn on until the powerhead and the bag are on correctly. Remember to test it, you don't have to put all the metal and trim back together. Once you have received your desired results you just simply have to put everything back together and then you are finished. We hope this has been a help to you. Thanks Great Vacs !

SERVICE@GREATVACS.COM