Replacement Rainbow Head Power Nozzle Brush from GreatVacs.com 

We get asked if we sell replacement Rainbow heads quite often! If you’ve ever gone looking for a genuine Rainbow head, you probably noticed that they can run you around $200. Today, Dustin shows you a replacement head that is NOT made by Rainbow, but that we’ve sold a lot of and our customers love. They’re less expensive, work great, and come with a geared belt so you’re not replacing belts!

 

 

 

These replacements head kits will work on all models of D3, D4, and SE. There are two types of connection: button lock and friction fit.

 

The kit uses friction fit to attach to your Rainbow hose. You simply insert the hose and twist to the right. To take it off just untwist it!

 

The power nozzle comes with a standard two-prong cord and you connect it the same way as you would the original Rainbow head.

 

To vacuum, turn on your Rainbow vacuum and then turn on the power head.

 

The power head features a stainless-steel brush roll and removable strips for the nylon brushes. It also has the red reset button at the back. The geared belt doesn’t slip and doesn’t need to be replaced.

 

Another great feature? It’s a standard head so the parts are readily available! It also has an access panel so you can easily see if anything is wrapped around your brush roll. One of the biggest power head killers is carpet fibers! When they get wrapped around your brush roll the motor can get burned out.

 

 

Gotta have one? You can find them here!

  

Want to know what Rainbow vacuum is best for you? Check out our Rainbow Vacuum guide!

 

Looking for more info? Check out our Education Center!

 

Need your Rainbow repaired? Send us an email at service@greatvacs.com

 

We sell Rainbow vacuums! We buy Rainbow vacuums! And we sell parts, tools, or anything else you need! If you need any parts, supplies or have any questions, email as service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all of our different products.

 

 

Replacement Rainbow Head Power Nozzle Brush from GreatVacs.com

Replacement Rainbow Head Power Nozzle Brush from GreatVacs.com 

We get asked if we sell replacement Rainbow heads quite often! If you’ve ever gone looking for a genuine Rainbow head, you probably noticed that they can...

Read more

How to Replace a Kirby Vacuum Hose End

Is your Kirby tool hose not attaching properly to the vacuum body? It may be due to a broken or worn out Hose End. Today we show you how to easily replace that old end piece.

 

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Tools

  • Needle nose pliers

 

Instructions

 

The first thing you will want to do is inspect your hose end. Check the long tab that engages the safety switch, the two hooks, and the three slots inside. If any of those are damaged, you will need to replace your hose end.

 

To remove the old hose end take your needle nose pliers and grab the rubber lip on the inside.

 

Then twist to the side. This will create a gap.

 

Now, push the needle nose pliers further into the gap and twist more, until the rubber lip folds in on itself. 

 

At this point you can take your other hand and press up on the hose end while you press the other direction with the pliers and they should come apart.

 

To get the new hose end on you will do the same thing. Take your needle nose pliers and twist the rubber part.

 

Hold the rubber piece with your hand and slide the new hose end over it.

 

Once it’s on you’ll notice that the rubber piece is still bent.

 

Simple take your finger and press it back out! You’re done!

 

Click Here to shop Kirby Vacuum Hose Ends

 

Which model of Kirby vacuum is the best? Here’s what we think!

 

Looking for more info? Check out our Education Center!

 

Need your Kirby repaired? Send us an email at service@greatvacs.com 

 

We sell Kirby vacuums! We buy Kirby vacuums! And we sell bags, belts, cords, or anything else you need!

 

Here at Great Vacs we’ve serviced and rebuilt nearly 100,000 Kirby vacuum cleaners, so if you have any questions or comments feel free to leave us a comment! You can also head on over to our YouTube channel to see more education videos.

 

How to Replace a Kirby Vacuum Hose End

How to Replace a Kirby Vacuum Hose End

Is your Kirby tool hose not attaching properly to the vacuum body? It may be due to a broken or worn out Hose End. Today we show...

Read more

How to Change a Kirby Vacuum Bag

Is it time to replace the bag in your Kirby Vacuum? Confused on where to start? Today we’ll go over the different styles of bags and how to change them on your vacuum.

 

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

“G” Style Generic Bag

 

The first step is to unzip the outer cloth bag.

 

Then pull out the fill tube to expose the inner bag.

 

Simply detach it from the fill tube!

 

Throw the old bag away and get your new bag. We will start with a generic bag, which has tabs as shown above.

 

You need to push the bag on until it goes past the tabs on the fill tube.

 

You may find it helpful to grab the bag by the top of the connection piece.

 

As you’re putting it on, give it a good twist and it should go on all the way. Once it’s on just tuck the bag back in the outer cloth bag and zip it up!

 

“G” Style Genuine Bag

 

If you’re using a genuine bag you’ll notice that it has tab slots. These make installation a breeze!

 

Just line the tab slots up with the tabs on the fill tube, push it on, and twist!

 

“F” Style Genuine Bag

 

Unzip the outer cloth bag and pull the inner bag out. You’ll notice that the F series has a tab. Since you’re throwing this bag away it’s fine to rip it off.

 

We’ll be starting with the genuine Kirby bag, which fits all models.

 

The tab on the top of the connector helps it fit the F series vacuums by folding over the clips on top of the fill tube.

 

Push the bag onto the fill tube, make sure the bag goes past the clip on the bottom, then fold down the tab on the top. Then put the inner bag back into the outer cloth bag, zip it up, and you’re good to go!

 

“F” series Generic Bag

 

The generic bag works with the same concept as the genuine. Start by pushing it on.

 

Then make sure the bottom clip goes over the bottom of the bag connection. Then tuck it away and zip the outer bag up. You're ready to get back to vacuuming!

 

Here at Great Vacs we’ve serviced and rebuilt nearly 100,000 Kirby vacuum cleaners, so if you have any questions or comments feel free to leave us a comment! You can also head on over to our Youtube channel to see more educational videos.

 

How to Change a Kirby Vacuum Bag

How to Change a Kirby Vacuum Bag

Is it time to replace the bag in your Kirby Vacuum? Confused on where to start? Today we’ll go over the different styles of bags and how to...

Read more

How to Replace a Kirby Vacuum Pivot Assembly


Is the transmission on your Kirby vacuum not engaging at the right time? Is your pivot broken, or is your handle not staying up like it’s supposed to? Then this is the video for you! We go over how to replace and properly adjust the pivot assembly on all G models of Kirby Vacuums.

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

Supplies

  • Pivot assembly
  • Torx bit driver
  • T15 torx bit
  • T20 torx bit
  • T25 torx bit


Instructions

First, disassemble your Kirby vacuum.

 



Once disassembled, you need to get the black cover off the back. Use the T15 bit and remove the screw for the cord holder. As you’re removing the screws set them in a safe location and remember which ones go where.

 

To remove the screw by the on/off button you need to switch to a T20. Remove the black cover and set aside.

 

Now, moving to the front of your Kirby vacuum, lift the lid. There are two screws holding on the main body cover. Use the T20 bit to remove them.

 

Move back around to the back and, using the same bit, remove the two screws that are holding on the main body cover.

 

Once the cover is removed there are two T25 screws holding in the pivot assembly. This is a great opportunity to tighten the screws if needed, or replace the pivot assembly.

 

On the back left side there is a little slot that has a tooth in it. Take that out and just like that, you can take your pivot assembly out.

 

Once you have the old pivot assembly out you can replace it with the new one.
Slide the new pivot assembly in, remembering that there is the slot that the tooth needs to go in.

This is important! As you’re putting it on, there are holes that you need to center directly above the screw holes. If it is too far forward or back it won’t allow the transmission to engage properly. We recommend just hand tightening the screws and then finishing with the T25.

 

Now, reinstall the main body cover. Switch out your torque bit with the T20 and replace the four screws that hold the cover in place.

 

Slide the black cover back into place over the cord holder. There is a slot for it to slide into. The screw to hold the cord holder in place is the smaller black T15 screw.

 

Finally, replace the larger black T20 screw at the bottom. Congratulations! You’re done.


This video can be used to replace, adjust, or tighten your pivot assembly.

If you need to purchase a pivot assembly click here.

Here at Great Vacs we’ve serviced and rebuilt nearly 100,000 Kirby vacuum cleaners, so if you have any questions or comments feel free to leave us a comment! You can also head on over to our Youtube channel to see more educational videos.

 

How to Replace a Kirby Vacuum Pivot Assembly

How to Replace a Kirby Vacuum Pivot Assembly


Is the transmission on your Kirby vacuum not engaging at the right time? Is your pivot broken, or is your handle not staying up like it’s supposed...

Read more