Kirby bag falling off?

Does your Kirby bag keep falling off? Tired of your Kirby vacuum not turning on due to your bag? Well, in this video we will go over a few things that will help fix this problem. We will also show you the proper way to put your bag on.

 

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Instructions

 

 

If you take the bag off by twisting counter-clockwise you will notice a small switch.

 

This switch needs to be pushed forward to engage the safety switch. This happens when the bag is attached properly.

 

You will also notice a tab on the end of the bag. This is how your bag engages the safety switch!

 

To make sure you bag is attached properly, take note of the brass pins on the vacuum and the three slots at the end of your bag.

 

Line the bag up on the brass pins and twist clockwise to lock it in place.

 

Maybe you've noticed that your bag pops out of place too easily! That could be a sign of a worn out part somewhere in the bag area. If that’s the case go ahead and send us an email with more details. Send a picture of the inside of the bag area and the attachment area if possible.

 

 

Which model of Kirby vacuum is the best? Here’s what we think!

 

Looking for more info? Check out our Education Center!

 

Need your Kirby repaired? Send us an email at service@greatvacs.com

 

We sell Kirby vacuums! We buy Kirby vacuums! And we sell bags, belts, cords, or anything else you need!

 

Here at Great Vacs we’ve serviced and rebuilt nearly 100,000 Kirby vacuum cleaners, so if you have any questions or comments feel free to leave us a comment! You can also head on over to our YouTube channel to see more education videos.

 

Kirby bag falling off?

Kirby bag falling off?

Does your Kirby bag keep falling off? Tired of your Kirby vacuum not turning on due to your bag? Well, in this video we will go over a few things that...

Read more

How to Attach A Tool Caddy to A Central Vacuum Wand 

When you purchase a new Central Vacuum Tool Kit, the number of tools and attachments can be overwhelming. In this video Kyle demonstrates how to attach and use the 3-Peg Tool Caddy.

 

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your machine, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

  

Instructions

 

This process work for either the GV or Prolux central hose kit. We will start the process by demonstrating it on the wand. You’ll notice two things: your wand has a button lock and none of your tools have a hole to accept this button lock. It’s okay, because the tools are friction fit and will still fit on the end of the wand. All you need to do is slide the tool on while pushing down the button lock.

 

The hose works the same way – just slide the tool on the end while pushing down the button lock and friction will keep it in place.

 

To attach the tool caddy to the extendable wand start by extended it out.

 

Take the tool caddy and firmly push it onto the wand. You’re done!

 

 

Check out our Central Vacuum Hose Kits:

Universal 30 ft Central Vacuum Hose Kit With Wessel Werk Power Nozzle

Premium Electric Prolux Universal Central Vacuum Hose Kit With Wessel Werk Power Nozzle

Premium Prolux Universal Central Vacuum Hose Kit With Turbo Nozzle

30' GV Universal Central Vacuum Hose With Tools

 

If you’re in the market for a new Central Vacuum, check out the Prolux CV12000!

 

If you need any parts, supplies or have any questions, email us at service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all of our products.

 

How to Attach A Tool Caddy to A Central Vacuum Wand

How to Attach A Tool Caddy to A Central Vacuum Wand 

When you purchase a new Central Vacuum Tool Kit, the number of tools and attachments can be overwhelming. In this video Kyle demonstrates how...

Read more

How to Perform Basic Vacuum Maintenance

No matter what type of vacuum you have, they all have one thing in common – they need to be maintained. Just like anything with moving parts, a lack of maintenance can cause premature wearing out of components that keeps your vacuum working at its best. In this video Kyle goes over some basic tips to keep your vacuum in tip top shape, and last for years to come!

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Instructions

 

We’ll start off going over why your vacuum cleaner may have poor performance. You could have a full bag or dirt bin, you could have a dirty, clogged filter, your head or hose could be clogged, the brush roll may be covered in hair, or you have seized brush roll bearings.

 

We will be using this specialty maintenance tool. To make it easy, we’re including this tool with most of the vacuums we sell!

 

First, we will go over how to change a full bag or dirt bin. Most vacuums have a full bag indicator light that is located on the canister, which makes it easy to know when you need to swap out the bag with a new one. If your vacuum cleaner uses a dirt bin, you can easily see when it needs to be emptied.

 

If your full indicator light comes on and the bag isn’t actually full, you may have a clog in the head, hose or wand. The vacuum will notice the decrease in suction and may assume the bag is full. To empty the bag you will first need to located the bag chamber. Once opened you will simply remove the bag, throw it away, and put in a new, empty bag. If your vacuum has a bag holder, make sure you don’t throw it away!

 

If your vacuum uses a dirt bin, it’s very simple. Just detach the bin from the vacuum, hold over the trash can, and open the trap door.

 

Next, we’ll go over dirty or clogged filter. If the filter is dirty or clogged it will reduce air flow and can cause the motor to overwork and overheat. This could, in turn, cause the motor to turn off for safety reasons. Most vacuums have a pre- and post-motor filters and you will find them behind a cover or in the bag chamber. Check both filters and clean them if they look dirty.

 

To clean the filters, start by removing them. Then give them a good smack with your hand to remove loose dirt.  Do this outside to avoid making a huge mess in your home.

 

Then, take the specialty tool and use the brush side to get deep down into the grooves. After you’re done the filter should look new again. You may have to repeat it a few times to get all the dirt out.

 

Now, we’ll go over a clogged head, hose, or wand. We mentioned earlier that there may be a clog if the full bag indicator light comes on without the bag actually being full. You may also notice reduced suction and pickup if there’s a clog. The head may even spit debris back out.

 

Start with the wand because it’s the easiest. You put it up to your eye and check to see if you can see light at the other end. If you can see straight through with no problem it isn’t clogged. Can’t see through? You’ve just found a clog!

 

To remove the clog you can use an air compressor, or, if you vacuum has a blower feature, you can use that. You can also use a broom handle or other straight, rigid item to push the clog out.

 

Next up is the hose. The easiest way to diagnose a hose clog is to hook it up to the vacuum, turn it on, and put your hand over the other end of the hose. If you can’t feel suction, or it's very poor, there is a clog or blockage in the hose. Dislodging the clog is the same as with the wand – either use a long, straight, rigid object to push it through, or use an air compressor or blower feature from the vacuum.

 

Lastly, we have the power head. The most common places for clogs are in the pivot neck or suction port. You may be able to access the clog through the pivot neck and just pull it out. Otherwise, the easiest way to remove is the clog is to take the power head apart. Most are held together with screws.

 

Take the screws out and remove the top portion from the power head. If you see a clog you should be able to easily remove it.

 

Another common reason for poor vacuum performance is a hair covered brush roll. We recommend removing the brush roll from the power head before removing the hair.

 

Once the brush roll is removed you can use the specialty tool to cut the hairs, and then grab and pull them off.

 

The last common problem we’ll be covering is seized brush roll bearings. This will prevent your brush roll from spinning, which will result in dirt or debris not being picked up. Depending on your brush roll, you may not be able to access the bearings. If that’s the case contact us and we’ll help you get a replacement brush roll.

 

When the brush roll has been removed from the vacuum you can use the specialty tool to brush away dirt, or use the razor to cut away hairs from the end where the bearings are.

 

If you need any parts, supplies or have any questions, email us at service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos.

 

 

How to Perform Basic Vacuum Maintenance

How to Perform Basic Vacuum Maintenance

No matter what type of vacuum you have, they all have one thing in common – they need to be maintained. Just like anything with moving parts, a lack...

Read more

You'll never guess what 5 things this vacuum can do!

 

Can a Rainbow Vacuum Cleaner blow air? Can it pickup wet and dry messes? Can it be used as a purifier? What about Pet Hair? All these questions and more are answered today as we learn 5 things Rainbow vacuums can do that you may not be aware of.

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

#1 – Blower/ Inflator

 

Rainbow vacuums can be used to blow of inflate simply by attaching the hose to the exhaust side! This is great for cleaning keyboards or dusting furniture and delicate electronics.

 

You can also use to clean places like automotive interiors and your engine bay.

 

Your Rainbow vacuum can also be used to quickly inflate air mattresses, beachballs, and inner tubes.

 

#2 – Wet and Dry Pickup

 

Rainbows are great for picking up pretty much anything – like spilled milk or water.

 

#3 – Air Purifying Mode

 

Rainbow vacuums are also great at cleaning air. They have HEPA and water filtration and are one of the best air purifiers on the market.

 

#4 – Pet Hair and Stair Cleaning

 

These vacuums are also great for cleaning up pet hair because of their excellent filtration and huge array of attachments.

 

One of the attachments is the Rainbow Mini Head, which is great for cleaning stairs without having to carry a heavy vacuum up and down.

 

#5 – Shampooing

 

With a few additional steps you can transform your Rainbow vacuum into a shampooing machine.  You can clean anything from low pile carpet to high pile carpet, tile, and any other water-safe hard floor surface. You can also easily transition from multiple surfaces to the next without needing to switch attachments.

 

Need to clean upholstery or auto interiors? There’s a hand held shampooer that is perfect for that!

 

 

Want to know what Rainbow vacuum is best for you? Check out our Rainbow Vacuum guide!

 

Looking for more info? Check out our Education Center!

 

Need your Rainbow repaired? Send us an email at service@greatvacs.com

 

We sell Rainbow vacuums! We buy Rainbow vacuums! And we sell parts, tools, or anything else you need! If you need any parts, supplies or have any questions, email as service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all of our different products.

 

You'll never guess what 5 things this vacuum can do!

You'll never guess what 5 things this vacuum can do!

 

Can a Rainbow Vacuum Cleaner blow air? Can it pickup wet and dry messes? Can it be used as a purifier? What about Pet...

Read more