How to Make Your Hose Fit Better on Prolux 2.0 Vacuums

If you’re having a hard time setting up your new Prolux 2.0, watch this video to see how to easily get your hose connected firmly to your vacuum and wand, so you’ll be ready to go in no time!

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Tools

  • Heat gun or hair dryer

 

Instructions

 

As you can probably tell, the elbow piece of the hose if very tight and difficult to get on the vacuum portion.

 

 

Take your heat gun or hair dryer and heat up the plastic elbow piece to where it’s more pliable.

 

Once it’s adequately heated, push the elbow piece onto the vacuum portion as far as it will go.

 

You will use this technique on the other end of the hose to make it fit better on the wand as well.

 

When you insert the wand end into the hose you will need to make sure the lip goes in as well.

 

 

Check out this video on how to set up your wands the right way.

 

What’s that? You don’t have the best bagless backpack vacuum in the world? You better get one! Check them out here!

 

Don't forget, GreatVacs is the only authorized dealer of Prolux products, so if you need any parts, supplies or have any questions, email as service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all Prolux products.

 

How to Make Your Hose Fit Better on Prolux 2.0 Vacuums

How to Make Your Hose Fit Better on Prolux 2.0 Vacuums

If you’re having a hard time setting up your new Prolux 2.0, watch this video to see how to easily get your hose connected...

Read more

How to Replace the Rear Wheel on a Prolux Tritan Vacuum

Accidentally throw your vacuum down the stairs again? Did the rear wheel fall off in the process? Well you’re in luck because in this video we show you how to remove and replace the wheels on the Prolux Tritan Canister Vacuum!

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Tools

  • Flat head screwdriver

 

Instructions

 

The rear wheels of the Prolux Tritan vacuum are held on by three tabs. To get them off you can pull the wheel away from the body a little and stick the screwdriver between the wheel and the body. Then, using the screwdriver, you can pry the wheel off.

 

To put a new wheel on, get two of the tabs latched.

 

Then take your flat head screwdriver and push the last tab in.

 

Now you can just push the wheel the rest of the way on and you’re done!

 

Don't forget, GreatVacs is the only authorized dealer of Prolux products, so if you need any parts, supplies or have any questions, email as service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all Prolux products.

 

How to Replace the Rear Wheel on a Prolux Tritan Vacuum

How to Replace the Rear Wheel on a Prolux Tritan Vacuum

Accidentally throw your vacuum down the stairs again? Did the rear wheel fall off in the process? Well you’re in luck because in this...

Read more

How to Clean a Brush Roll

Sometimes, when vacuum cleaners start to lose suction or just aren’t picking up as well it’s because the brush roll has too much hair wrapped around it. It is a good idea to regularly check your vacuum’s brush roll and remove hair as it builds up.

In this video, we show you how to clean almost any brush roll using our amazing technique!

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

Instructions

 

In this video we show two different brush rolls – one from a Kirby vacuum cleaner and the other from a Rainbow. They both have quite a bit of hair wrapped around them and we’ll be using a straight razor to remove it. A hook blade works best, but for this demonstration we’re using a straight one.

 

Remember: never cut toward yourself! Just take your blade and cut the hair away from yourself. It may take a few passes to get all of the hair.

 

When you’ve cut through the hairs you can start grabbing handfuls and pull it from the brushes.

 

For the Kirby brush we’ll demonstrate a new specialty tool, which will be available on our website soon. It was designed to remove hair from brush rolls!

 

To use it, just slide the hook under the hair and slide it along the surface of the brush roll. As you do, the hook will catch the hairs and the blade will cut through them.

 

Same as above – as you cut through clumps of hair you’ll be able to pull it from the brushes and discard.

 

If you need any parts, supplies or have any questions, email us at service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos.

 

How to Clean a Brush Roll

How to Clean a Brush Roll

Sometimes, when vacuum cleaners start to lose suction or just aren’t picking up as well it’s because the brush roll has too much hair wrapped around it. It is...

Read more

How to Use the Prolux 2.0 Wands

If you’re having a hard time setting up your new Prolux 2.0, watch this video to see how to extend and properly set up your wand in no time!

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Instructions

 

The picture above shows the main wand that comes with the standard 2.0 kits.

 

The lower portion of the wand is contained inside the larger portion and sticks out as seen here.

 

The remove the lower portion you will need to unclamp the locking mechanism, grab the end, twist, and pull.

 

If you’re having trouble removing this section you may need to loosen the set screw, which is shown in the picture above.

 

 

What’s that? You don’t have the best bagless backpack vacuum in the world? You better get one! Check them out here!

 

Don't forget, GreatVacs is the only authorized dealer of Prolux products, so if you need any parts, supplies or have any questions, email as service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all Prolux products.

 

How to Use the Prolux 2.0 Wands

How to Use the Prolux 2.0 Wands

If you’re having a hard time setting up your new Prolux 2.0, watch this video to see how to extend and properly set up your wand in no...

Read more