How to Clean a Brush Roll

Sometimes, when vacuum cleaners start to lose suction or just aren’t picking up as well it’s because the brush roll has too much hair wrapped around it. It is a good idea to regularly check your vacuum’s brush roll and remove hair as it builds up.

In this video, we show you how to clean almost any brush roll using our amazing technique!

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

Instructions

 

In this video we show two different brush rolls – one from a Kirby vacuum cleaner and the other from a Rainbow. They both have quite a bit of hair wrapped around them and we’ll be using a straight razor to remove it. A hook blade works best, but for this demonstration we’re using a straight one.

 

Remember: never cut toward yourself! Just take your blade and cut the hair away from yourself. It may take a few passes to get all of the hair.

 

When you’ve cut through the hairs you can start grabbing handfuls and pull it from the brushes.

 

For the Kirby brush we’ll demonstrate a new specialty tool, which will be available on our website soon. It was designed to remove hair from brush rolls!

 

To use it, just slide the hook under the hair and slide it along the surface of the brush roll. As you do, the hook will catch the hairs and the blade will cut through them.

 

Same as above – as you cut through clumps of hair you’ll be able to pull it from the brushes and discard.

 

If you need any parts, supplies or have any questions, email us at service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos.

 

How to Clean a Brush Roll

How to Clean a Brush Roll

Sometimes, when vacuum cleaners start to lose suction or just aren’t picking up as well it’s because the brush roll has too much hair wrapped around it. It is...

Read more

How to Replace the Brush Roll and Belt on a GV Power Head 

If you own a GV powerhead, and need to replace the brush roll or belt, this video is for you!

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Tools

  • Phillips head screwdriver

 

Instructions

 

There are 8 screws on the underside of your GV powerhead.

 

Once those screws are removed (and set aside in a safe place), you can turn your powerhead over and remove the top portion.

 

If you want more room to work with you can remove this connector and set the top to the side.

 

Now you can easily access the brush roll and the belt.

 

To remove the brush roll, firmly grab the it and pull upwards.

 

Then slide the belt off of the motor shaft.

 

To replace these parts, insert the new belt over the motor shaft.

 

Then take your new brush roll and insert it into the belt, line up the ends, and pop it into place.

 

You may need to rotate the brush roll by hand a few times to make sure the belt aligns itself properly.

 

Take the top of the powerhead and make sure you reconnect the connector (if you unplugged it.)

 

Place the top portion back on.

 

Flip it over and put the 8 screws back in. Voilà! You replace the brush roll and belt on your GV power head!

If you need any parts, supplies or have any questions, email us at service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all Prolux products.

 

How to Replace the Brush Roll and Belt on a GV Power Head

How to Replace the Brush Roll and Belt on a GV Power Head 

If you own a GV powerhead, and need to replace the brush roll or belt, this video is for you!

 

Read more

How to Assemble a ProTeam Tool Kit

We sell ProTeams and ProTeam accessories. And today, Kyle will show you how to put a ProTeam tool kit together, and make sure it stays together.

These kits are 1 ½ inch diameter and will work with many brands of commercial backpack vacuums, including our GV 6QT backpack vacuum!

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you.  

Instructions

 

In this video we are using a standard 1.5” ProTeam tool kit, which is found on most ProTeams on the market. The kit includes a hose, two wands, a floor tool, and some general attachments.

 

We will start with the wands, since these usually give people the most trouble.

 

The bare wand, with no plastic at the ends, is the upper wand portion.

 

The other wand, with plastic on each end, is the lower wand portion.

 

The end with the twisting collar is where you will insert your attachments.

 

The other end with the locking mechanism will keep the top wand in place.

 

To connect the wands, start by taking the upper wand portion. You will notice that there is a groove.

 

In the lower wand portion, there is a raised plastic notch.

 

Just line the notch up with the groove and slide the upper portion in.

 

If you’re having trouble sliding them together, take a Phillips head screw driver and loosen the set screw at the locking mechanism.

 

Once you’re at your desired height you can lock the tab down.

 

Once the wands are together you can attach your tools. If you were to remove the twisting collar at the end of the lower wand portion and look inside, you’d see a metal brass C ring. As you tighten the collar down this ring will close on the grooves located on the tool, which keeps it from falling off as you clean.

 

Insert your attachment and tighten the plastic collar. As you do so make sure the ring sits in the groove. If your tools are falling off, make sure you are tightening the collar all the way and that the metal ring is seated in the groove.

 

Lastly, take the hose part of the kit. You will notice that the hose has two different ends. One is straight and the other has a 90-degree elbow. The elbow goes into the top of your ProTeam and the straight end attaches to the upper wand portion.

 

The upper wand portion has this raised section at the end.

 

To connect the hose, you will just push it on until it is over the raised groove. If the hose seems too stiff and won’t go on you can use a hair drier to soften the plastic.

 

Buy the kit shown in the video here!

 

Want the ProTeam ProBlade kit? You can buy that here!

 

If you need any parts, supplies or have any questions, email us at service@greatvacs.com or leave a comment! You can also head on over to our YouTube channel to see more educational videos on all of our different products.

 

How to Assemble a ProTeam Tool Kit

How to Assemble a ProTeam Tool Kit

We sell ProTeams and ProTeam accessories. And today, Kyle will show you how to put a ProTeam tool kit together, and make sure it stays together.

These kits...

Read more

The GV Electric Power Nozzle Kit for Backpack Vacuums 

In this video, we show how to assemble and attach the GV Electric Power Nozzle Kit to a backpack vacuum. This kit works with almost any backpack vacuum with a 1 ½” hose.

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

When you get the electric power nozzle kit, it will contain a three-way adapter cord, and electric main hose, a main extendable wand, and a GV power head.

 

Start by taking the three-way adapter and plug one end into the power source on your backpack vacuum.

 

Take the other end and plug it into your extension cord.

 

If you haven’t done so already, insert your extendable main wand into your power head.

 

Take the main hose and attach it to the wand. You may need to push the button lock down to get it to click into place correctly.

 

Take the power head two-prong cord and plug it into the back of the main hose.

 

Take the main hose and insert the other end into the backpack vacuum.

 

Take the three-way adapter cord and plug the two-prong cord into it.

 

And just like that, you’ve hooked up your GV electric power nozzle to your backpack vacuum!

 

Now that everything is hooked up, you’re ready to vacuum!

 

First, extend the extendable wand by pushing upwards on the black button and pulling the wand out.

 

The release the pivot by pressing down on the foot pedal.

 

 

Turn the switch on the handle to the “On” position.

 

Then turn the power head on by stepping on the button on the left side and then turn your vacuum on.

 

Enjoy!

 

We sell these kits for GV 6qt, 8qt, and 10qt backpack vacuums, as well as ProTeams! Click here!

 

We also sell replacement power nozzle kits for Rainbow Vacuums!

 

If you need any parts, supplies or have any questions, email as service@greatvacs.com or leave a comment! You can also head on over to our Youtube channel to see more educational videos on all Prolux products.

 

The GV Electric Power Nozzle Kit for Backpack Vacuums

The GV Electric Power Nozzle Kit for Backpack Vacuums 

In this video, we show how to assemble and attach the GV Electric Power Nozzle Kit to a backpack vacuum. This kit works with almost any...

Read more