My Kirby Won't Turn On! Safety Switches and Other Common Problems 

Are you having trouble getting your Kirby vacuum to turn on? Today we go over a few common problems that may keep your Kirby from working the way it should.

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Instructions 

 

If your Kirby vacuum isn’t turning on, the first thing you’ll want to do is check the safety switches. We’ll start with the one behind the power nozzle.

 

Start by releasing the belt.

 

Now release the latch.

 

When you take the powerhead off, you’ll be able to see the safety switch.

 

When you put the head on, a small tab will press this safety switch. It should be sticking out about half an inch or so. If it looks short or has a jagged, broken edge, then you tab is probably broken and isn’t engaging the safety switch. The solution is to replace the power head and we can help you with that! Just email us at service@greatvacs.com with more details.

 

If your tab looks good, you’ll want to be sure you’re attaching the head properly. There is a bar on the vacuum and two hooks on the power head. These hooks will need to hook over the bar.

 

Raise the height of the vacuum all the way to make it easier, then attach the head.

 

Secure the latch and engage the belt. The power head should only have a slight, 1-2 mm gap. If yours looks like the one pictured above you should be good!

 

The next safety switch is by the bag. If you remove the bag, you’ll notice this tiny switch on the vacuum.

 

There is a tab on the bag that pushed the switch forward when attached properly.

 

For the bag to be attached properly it will need to be aligned on the three brass tabs.

 

Set the bag on the tabs and turn clockwise until you feel it lock into place.

 

 If any of these tabs are broken the bag may not engage the switch. Also, if you notice the bag is popping back out of place too easily that could be a sign something is worn out and needs replaced.

 

If you’ve checked your safety switches and those all work and it’s STILL not turning on you should check the power cord. Unwind the cord and try wiggling it around as you attempt the turn the vacuum on. If the vacuum turns on at some point you likely have a short in the power cord. If that happens send us an email at service@greatvacs.com and we can help replace the cord.

  

Which model of Kirby vacuum is the best? Here’s what we think!

 

Looking for more info? Check out our Education Center!

 

Need your Kirby repaired? Send us an email at service@greatvacs.com

 

We sell Kirby vacuums! We buy Kirby vacuums! And we sell bags, belts, cords, or anything else you need!

 

Here at Great Vacs we’ve serviced and rebuilt nearly 100,000 Kirby vacuum cleaners, so if you have any questions or comments feel free to leave us a comment! You can also head on over to our YouTube channel to see more education videos.

 

My Kirby Won't Turn On! Safety Switches and Other Common Problems

My Kirby Won't Turn On! Safety Switches and Other Common Problems 

Are you having trouble getting your Kirby vacuum to turn on? Today we go over a few common problems that may keep your Kirby...

Read more

How to Replace a Kirby Vacuum Hose End

Is your Kirby tool hose not attaching properly to the vacuum body? It may be due to a broken or worn out Hose End. Today we show you how to easily replace that old end piece.

 

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

Tools

  • Needle nose pliers

 

Instructions

 

The first thing you will want to do is inspect your hose end. Check the long tab that engages the safety switch, the two hooks, and the three slots inside. If any of those are damaged, you will need to replace your hose end.

 

To remove the old hose end take your needle nose pliers and grab the rubber lip on the inside.

 

Then twist to the side. This will create a gap.

 

Now, push the needle nose pliers further into the gap and twist more, until the rubber lip folds in on itself. 

 

At this point you can take your other hand and press up on the hose end while you press the other direction with the pliers and they should come apart.

 

To get the new hose end on you will do the same thing. Take your needle nose pliers and twist the rubber part.

 

Hold the rubber piece with your hand and slide the new hose end over it.

 

Once it’s on you’ll notice that the rubber piece is still bent.

 

Simple take your finger and press it back out! You’re done!

 

Click Here to shop Kirby Vacuum Hose Ends

 

Which model of Kirby vacuum is the best? Here’s what we think!

 

Looking for more info? Check out our Education Center!

 

Need your Kirby repaired? Send us an email at service@greatvacs.com 

 

We sell Kirby vacuums! We buy Kirby vacuums! And we sell bags, belts, cords, or anything else you need!

 

Here at Great Vacs we’ve serviced and rebuilt nearly 100,000 Kirby vacuum cleaners, so if you have any questions or comments feel free to leave us a comment! You can also head on over to our YouTube channel to see more education videos.

 

How to Replace a Kirby Vacuum Hose End

How to Replace a Kirby Vacuum Hose End

Is your Kirby tool hose not attaching properly to the vacuum body? It may be due to a broken or worn out Hose End. Today we show...

Read more

How to Change a Kirby Vacuum Bag

Is it time to replace the bag in your Kirby Vacuum? Confused on where to start? Today we’ll go over the different styles of bags and how to change them on your vacuum.

 

 

Important Safety Tips

  • Always make sure your machine is unplugged and the power button is turned off, before servicing your vacuum.
  • Always make sure your hands are dry and free from moisture before servicing your machine.
  • Be sure to wear gloves when servicing your machine to prevent any cuts or scrapes.
  • If you are uncomfortable working on your vacuum, please don’t hesitate to contact us at service@greatvacs.com and we can help you through the process or you can send it into us to fix it for you. 

 

“G” Style Generic Bag

 

The first step is to unzip the outer cloth bag.

 

Then pull out the fill tube to expose the inner bag.

 

Simply detach it from the fill tube!

 

Throw the old bag away and get your new bag. We will start with a generic bag, which has tabs as shown above.

 

You need to push the bag on until it goes past the tabs on the fill tube.

 

You may find it helpful to grab the bag by the top of the connection piece.

 

As you’re putting it on, give it a good twist and it should go on all the way. Once it’s on just tuck the bag back in the outer cloth bag and zip it up!

 

“G” Style Genuine Bag

 

If you’re using a genuine bag you’ll notice that it has tab slots. These make installation a breeze!

 

Just line the tab slots up with the tabs on the fill tube, push it on, and twist!

 

“F” Style Genuine Bag

 

Unzip the outer cloth bag and pull the inner bag out. You’ll notice that the F series has a tab. Since you’re throwing this bag away it’s fine to rip it off.

 

We’ll be starting with the genuine Kirby bag, which fits all models.

 

The tab on the top of the connector helps it fit the F series vacuums by folding over the clips on top of the fill tube.

 

Push the bag onto the fill tube, make sure the bag goes past the clip on the bottom, then fold down the tab on the top. Then put the inner bag back into the outer cloth bag, zip it up, and you’re good to go!

 

“F” series Generic Bag

 

The generic bag works with the same concept as the genuine. Start by pushing it on.

 

Then make sure the bottom clip goes over the bottom of the bag connection. Then tuck it away and zip the outer bag up. You're ready to get back to vacuuming!

 

Here at Great Vacs we’ve serviced and rebuilt nearly 100,000 Kirby vacuum cleaners, so if you have any questions or comments feel free to leave us a comment! You can also head on over to our Youtube channel to see more educational videos.

 

How to Change a Kirby Vacuum Bag

How to Change a Kirby Vacuum Bag

Is it time to replace the bag in your Kirby Vacuum? Confused on where to start? Today we’ll go over the different styles of bags and how to...

Read more